Leather Doctor® Kit-B7, Bicast leather sticky topcoat refinishing kit is an innovative system developed for Bicast leather to restore finishes sticky problem. The sticky problem is often described from owners as follows. The finish gone dull on the seating areas and any material comes in contact sticks to it. The finishes feels a bit rubbery but after 5mins of sitting clothing were stuck to it. The location that suffers tackiness also reveals roughness to the touch. When sitting down and getting up, there is the sound of tape pulling and you can actually see a pattern on the couch from the jeans. If these experiences sound familiar then this kit is the answer. Stripping the surface contamination is done with Degreaser-2.2 and the help of Eraser-4 for better traction to removed surface materials. Suspended soiling is towel extracted and rinse with Acidifier-2.0. 2000-grit sandpaper or coarser to match is used to smooth rough surface. A 10% Crosslinker-25 is added to the BicastTop-76G for extra finish strength from stickiness. Protector-B (scentless) imparts a non-stick buttery-feel against sticky soiling; a rub-resistant against friction wear (optional Protector-B+ leather scented version diffuses a leather scent that enhances leather sensuous and luxuriously). This kit comes with reduced weight option to save on shipping thus Acidifier-2.0 and Protector-B has to be cut or filled up with distilled water accordingly prior to use. This starter kit is design as a holistic system; optional adds-on and refills are available as individual bottles - see link to individual products below . . . Average of 3 coatings BicastTop-76G (120ml) covers approximately 40 square feet. Note that bristle brush in picture is replace with 2 pieces of foamBrush-3 instead.
Step-1 Preparation: 1- Protect floor with plastic covering from over-spray and drips prior to restorative cleaning and stripping accumulated soiling. 2- CleanPro-1.5 is spray and work with horsehair Brush-1 and Eraser-4 and towel extracted until towel shows clean. 3- Use the Eraser-4 sponge side for normal cleaning and the crepe side for extra scrub from embedded materials. 4- Degreaser-2.2 is used in combination on the body contact oil and grease areas especially to the headrest and the hand-rest. 5- Shake the Degreaser-2.2 from separation to gel prior to use. 6- Apply by brushing with Brush-1 and/or scrubbing with Eraser-4 to remove surface soiling. 7- Suspended soiling is extracted with a lint-free towel or cleaning sponge until towel shows clean. 8- Spray Acidifier-2.0, agitate with Brush-1 and Eraser-4 and extract until towel shows clean again. 9- Inspect for reduced tackiness, otherwise spray soaks Towel-T5 with Acidifier-2.0 and place until towel dries for inspection. 10- When dry, sand surface roughness and ensure free of foreign material. 11- Surface is ready for topcoat application when smooth and free of residues.
Dry Preparation Prior to Topcoat Refinishing, Note:Ensure that all deteriorated topcoat is thoroughly sand off with an oscillating sander using sanding grit, 800, 1000 to 1200. Inspection is done with our slightly damp fingers to detect any such stickiness prior to topcoat refinishing commencing from Step-2.
Step-2 Refinishing: 1- Empty the Crosslinker-25 25gm bottle (about 10%) into the BicastTop-76G 220gm bottle and swirl very well. 2- Once the topcoat is cross-linked, it is best to used within 8 hours, otherwise it will be cured hard and be useless. 3- Apply by foamBrush-3 lightly to avoid streaks or finer soft varnishing brushes for streaks free result or airbrushing for professional result. 4- Dabbing with bristle brush reduces streaks as well as using a roller sponge. 5- Steaks are corrected by fine sanding when dry. 6- Use a hair dryer for speed drying in-between coats to satisfaction. 7- Let it overnight cure before non-stick Protector-B application.
Note: Test for satisfaction otherwise post your pictures and problem to http://www.leathercleaningrestorationforum.com/forum/forumdisplay.php?55-Upholstery-Bicast-Faux-Vinyl-Simulated-Leather for consultation prior to Step-3.
Step-3 Protection: 1- Protector-B is applied evenly with either foamBrush-3 or Towel-5 and is ready for use when dry. 2- For routine application, a paper towel is recommended to simultaneous soiling extraction.
Kit Content and Product Description:
Leather Doctor® Degreaser-2.2 (120ml) http://www.leatherdoctor.com/degreaser-2-2/ This is a waterbased pH 2.2 high viscosity formulated leather degreaser. It is for degreasing leather of oil, grease and sweat stains from skin and hair contact. Suspended soiling is thereafter rinse off with Acidifier-2.0 to a squeaky-feel.
Leather Doctor® Acidifier-2.0 (250ml) http://www.leatherdoctor.com/acidifier-2-0/ This a water-based pH 2.0 leather acidifier to rinse and pH balance tackiness from body oil, grease and sweat contamination.
Leather Doctor® BicastTop-76G (120gm) http://www.leatherdoctor.com/bicasttop-76g-gloss/ BicastTop-76 is a heavy-duty gloss topcoat design for bicast leathers. This is a water-based fine particular size urethane-resin emulsion to protect Bicast finishes with excellent toughness and flexibility. To rectify sticky or tacky finishes problem, an up to 10% of Crosslinker-25 is added prior to application.
Leather Doctor® Crosslinker-25 (12gm) http://www.leatherdoctor.com/crosslinker-25/ This is an auxiliary for refinishing topcoats to improve adhesion properties and increase top coat film strength. This is a high solid, polyaziridine crosslinker, without the VOC (volatile organic compound). It is super-concentrated and when incorporating a 10% to the topcoat it will significantly boost adhesion. By creating a tougher film that also ties up some of the hydrophilic elements.
Leather Doctor® Protector-B (250ml) http://www.leatherdoctor.com/protector-b/ This is a scentless (leather scented version use Protector-B+), non-film forming, non-stick, rub-resistant protector that impart a natural buttery-feel. Its non-stick breathable barrier is essentially to shield the detrimental effects of sticky soiling. Its natural buttery-feel protection increases the leather resistance to wet and dry rubs, thus reduce stretch, scuff and abrasion. It reduces friction squeaks that wear the finishes and helps prolong the finishes.
LeatherBrush-1 (1pc) http://www.leatherdoctor.com/leatherbrush-1/ This horsehair detailing brush is designed ergonomically to be an extension of our hand with a sturdy grooved grip. It is designed to produce effective result easily and efficiently. It is recommended for all smooth leather for a soft and scratch-free cleaning. Its length is 7 inches with a three-row bristle 1½ inches cleaning head. For fast cleaning swing the brush like a car screen wiper.
Towel-5 (5 pc) http://www.leatherdoctor.com/towel-5/ This towel works like cloth, lint free, highly absorbent, washable and stretchable. General application is for extracting suspended soiling or for spreading hydrator, fatliquor or protector. It is used for both dye and topcoat padding for smooth leathers. Also used for ‘reverse transferring’ of dye stains.
FoamBrush-3 (1 pc) http://www.leatherdoctor.com/foambrush-3/ This is dense foam that resists tearing and shredding and carries more material. It has a solid wood handle that allows greater control for quality results. It is used for controlling and spreading fatliquor for a more even distribution.
Sand2000 (1 pc) http://www.leatherdoctor.com/sand-2000/ This 2000grit sandpaper is selected to smooth in-between dried topcoat application when necessary.
LeatherEraser-4 (1 pc) http://www.leatherdoctor.com/leathereraser-4/ This is a 2½ x 2¼ x ¾ inch foam rubber sponge block with a crepe side for effective dry/wet traction soil removal.