Leather Perforated Auto Seat Bloodstain Remover - Kit-At5.bs

Perforated Leather Auto Seat Bloodstain Remover - Kit-At5.bs by Leather Doctor is formulated to remove coagulating and rusty bloodstains. Old bloodstains do coagulates and dried bloodstains may range from tan to dark brown with an outer ring. Dried deposits are gently brush, thereafter LeatherProteinCleaner-9.9 is applied with gentle agitation until it starts to dissolve and run. LeatherAcidifier-2.0 is use to neutralize and rinse remaining residue. LeatherTarnishCleaner-1.3 continues to works on the rusty trace of the stain until naturally dry. This below leather pH neutral (ISO-electric point or pI) of 1.3 need to be pH balanced with LeatherBasifier-8.8 with a pH value of 8.8 to bring the leather pH chemistry integrity to its pH neutral of 3 - 5. As some stains and working products may be absorbed, an inter-fibrillary colloidal water movement is further facilitated with LeatherHydrator-3.3, to move suspended stains and working products residue to resurface prior to fatliquoring (fat and oil replenishing). LeatherFatliquor-5.0 to rejuvenates the leather for suppleness when dry. LeatherProtector-B enhances a non-stick rub-resistant protection with a buttery-feel that shield against sticky soiling. Note that the mentioned products suffix numbers denotes its pH value for a holistic leather-safe bloodstain removal process. This kit comes with reduced weight to save on shipping thus all the concentrates in the bottles has to be cut/mix and fills with distilled water prior to use.

Instruction . . .

A- Protein Stain Cleaning: 1- Inspect and remove all caked and surface deposit prior to application. 2- Apply LeatherProteinCleaner-9.9, agitate with Brush-1 or a blunt bamboo skewers until it starts to dissolve and run, then extract with repetition until the stain is removed.

B- Protein Stain pH Neutralizing: 1- Neutralize and rinse with mandatory LeatherAcidifier-2.0 until towel shows clean to a squeaky feel. 2- Towel dries and inspect for satisfaction. 3- Any rusty appearance is treated with LeatherTarnishCleaner-1.3 when it is perfectly dry, otherwise skip to E- Hydrating.

C- Rust Stain Cleaning: 1- Rust component of the bloodstain is treated by redox (reduction-oxidation) reaction when the stain is dry. LeatherTarnishCleaner-1.3 is applied neatly with a cotton swab or heavier stain with a wet out towel-5 cut to size and place above the stain. 2- The product is left to work until it dries for inspection. For heavier stain may require repeat treatment, otherwise proceed immediately to pH neutralizing it.

D- Rust Stain pH Neutralizing: The residue of the low pH value LeatherTarnishCleaner-1.3 (pH1.3) is mandatory to be pH neutralized from denaturing the leather. 1- Basifier-8.8 (pH8.8) is applied over the LeatherTarnishCleaner-1.3 and towel extracted matching the amount of LeatherTarnishCleaner-1.3 being used earlier to totally neutralizing it out.

E- Hydrating: It is normal for leather to be stiff as it dries and need to be hydrated to relax the leather structure pre-conditioning it prior to fatliquoring. 1- The thickness of the leather is saturated to an optimum level with moisture oozing out when gently pressed between thumb and fingers with LeatherHydrator-3.3. 2- The leather is cover up with plastic wrapping to control evaporation and let it dwell up to 72hrs for complete hydration or saturation. 3- It is then manipulate by staking, stretching, massaging or cross flexing to relax the leather to satisfaction. 4- With satisfaction and allowing up to 25% combine moisture content or when a cotton dry towel remains dry from wiping and the leather is still damp with LeatherHydrator-3.3, fatliquoring begins before the leather is completely dry.

F- Fatliquoring: 1- LeatherFatliquor-5.0 is applied and brush with horsehair Brush-1 into the leather structure, as about 83.33% of water content evaporates, more is applied until the leather is fully saturated (intending to achieve an average of 14% of fat and oil when dry). 2- The fat liquored leather is left to slow dry and any surface shining residue is driven into the leather structure by brushing in conjunction with LeatherHydrator-3.3 until milky residue if any turns crystal clear. 3- The surface clear moisture is extract with a cotton towel until towel shows dry. 4- Begin staking, stretching, massaging or cross flexing one more time before the leather is completely dried for the desired suppleness.

G- Protecting: 1- Apply LeatherProtector-B or LeatherScentedProtector-B+ for reduce friction wears and imparting a non-stick surface against soiling with a natural buttery-feel spread with foamBrush-3” and is ready for used when dry.

Kit Content and Product Description:

Leather Doctor LeatherProteinCleaner-9.9 (250ml) is a pH9.9 cationic specialty solution formulated for removing blood and other protein based stains. In addition, any staining that comes from a living animal or person will probably need this product in the removing process. It is mandatory to follow with LeatherAcidifier-2.0 to rinse and pH balance the alkalinity as a holistic leather-safe system, thus safe for all leather, vachetta, suede, nubuck, hair-on, woolskin and feather. Compound blood stains are further treated with LeatherTarnishCleaner-1.3 and pH balanced with LeatherBasifier-8.8. Tips: Bloodstains tend to coagulate and bind tenaciously, thus using an appropriate tool like a bamboo skewers helps to dislodge the stain. Note: Bloodstain is protein based that has the tendency to coagulate with the leather protein fiber and makes removal tougher than other protein stains even working with appropriate leather protein stain removal. It has also the iron component that will get darker in color when it ages. Dried blood stains will range from tan to black with an outer ring. When the protein component is first removed with LeatherProteinCleaner-9.9 and rinse with LeatherAcidifier-2.0 neutralizing effect, the other secondary iron component present will need to go through another redox (reduction-oxidation) chemical reaction again when dry and neutralized with LeatherBasifier-8.8. Thereafter, other option available is by leather rejuvenating and color refinishing to camouflage remaining residue from compounded and failed attempted stains. Hydrogen peroxide, as an example is not recommended for bloodstain removal on leather, as oxidation will “cook” the protein leather fiber, altering their original chemistry composition.

Leather Doctor LeatherAcidifier-2.0 (250ml) is a water-based pH2.0 leather acidifier rinse formulated for neutralizing high alkalinity product such as LeatherProteinCleaner-9.9 (pH9.9) to its leather pH neutral (ISO-electric point or pI) value of 3 - 5. As a standalone, it is use for pH balancing alkaline overexposure that manifest as marks, streaks, brightness and tackiness. This universal acidifier is leather-safe for all leather types including pigmented, aniline, vachetta, nubuck, suede, hair-on-hide and woolskin leather types.

Leather Doctor LeatherTarnishCleaner-1.3 (30ml) is a water-based pH1.3 redox (reduction-oxidation) leather tarnish stain remover. It is for removing metal stains like rust, tarnish, some ink and dye including urochrome-yellowing effect. In addition, any stain that is metals derived will probably be removed with this product. This universal tarnish stain remover is for all leather types including pigmented, aniline, vachetta, nubuck, suede, hair-on-hide and woolskin. However, its low pH value will need to be highly pH balanced with LeatherBasifier-8.8 (pH8.8) to its leather pH neutral (ISO-electric point or pI) of 3 - 5 from denaturing.

Leather Doctor LeatherBasifier-8.8 is a water-based pH8.8 mild leather basifier formulated to neutralize strong acidic exposure especially after LeatherTarnishCleaner-1.3 from denaturing. This universal basifier is for all leather types including pigmented, aniline, vachetta, nubuck, suede, hair-on-hide and woolskin leather types.

Leather Doctor LeatherHydrator-3.3 (250ml) is a water-based pH3.3 leather-safe hydrator. It is mainly used as a fat-liquoring pre-conditioner with multi functional abilities. Surface application is primary to check for even surface tension free of blotchiness prior to fatliquor replenishing. Structural application will require saturating to an optimum level with moisture oozing out when gently pressed between thumb and fingers. This universal Hydrator-3.3 is for all leather types including pigmented, aniline, vachetta, nubuck, suede, hair-on-hide and woolskin. The multi functional abilities include: A - Surface Tension Inspection. B - Leather Stiffness and Unnatural Creases Rectification. C - Structural Cleaning. D - Dye Bleeding, Leather Tackiness and Stiffness Rectification. E - Dye Fading Rectification. F - Reverse-Transfer Suspended Soiling. G - Leather pH Chemistry Integrity Rectification. H - Fatliquor Surface Residue Cleaning. I - Leather Shrinkage Rectification. A - Surface Tension Inspection: Surface tension prevents liquid penetration and may result in undesired blotchiness with uneven absorption. Surface tension inspection is for even appearance of even absorption rate prior to Fatliquor-5.0 application. Instruction: A1 - The leather surface to be fatliquored is lightly mist spray with Hydrator-3.3 evenly and wipe with lint free towel to free of surface tension prior to fatliquoring. It is then let to slow dry. A2 - Fatliquored surface residue sheen when dry if any, is driven into the leather structure with Hydrator-3.3 in conjunction with appropriate brushes, converting milky residue if any to crystal clear. A3 - The crystal clear moisture is towel extracted until towel shows dry. A4 - When almost dry of up to 25% combine moisture content the leather is stake, stretch or massage to complete dry for desired suppleness. B - Leather Stiffness and Unnatural Creases Rectification: Leather stiffness is fibers structure that becomes stick together when leather commonly gets wet and in most cases fatliquor leaches out. Severe stiffness results when leather lost its fatliquor under heat over-exposure and should be handle with caution from cracking it. Leather creases are unnatural wrinkles resulting from the collapsing empty leather fiber structure due to diminishing fatliquor (fat and oil) content. To plumps, relaxes and separates crushed, shrunk and stick together fibrils by manipulating away-unwanted stiffness and unnatural creases is as follows: Instruction: B1 - The thickness of the leather is saturated to an optimum level with moisture oozing out when gently pressed between thumb and fingers with Hydrator-3.3. B2 - The leather is cover up with plastic wrapping to control evaporation and let it dwell up to 72hrs for complete hydration or saturation. B3 - It is then manipulate by staking, stretching, massaging or cross flexing to relax the leather to satisfaction. B4 - With satisfaction and allowing up to 25% combine moisture content or when a cotton dry towel remains dry from wiping and the leather is still damp with Hydrator-3.3, fat liquoring begins before the leather is completely dry. B5 - The fat liquored leather is left to slow dry and any surface shining residue is driven into the leather structure by brushing in conjunction with Hydrator-3.3 until milky residue if any turns crystal clear. B6 - The surface clear moisture is extract with a cotton towel until towel shows dry. B7 - Begin staking, stretching, massaging or cross flexing one more time before the leather is completely dried for the desired suppleness. Best result is manipulating the leather structure to dryness for extra desired suppleness. C - Structural Cleaning: Structural cleaning is cleaning penetrated soiling or foreign contamination from below surface. This process includes the following steps: Instruction: C1 - The leather is hydrated with Hydrator-3.3, depends on severity up to 72hours dwelling is recommended to moves the soiling upwards. C2 - To maintain a consistent moisture level, the leather in question may be seal in container or plastic wrapping with periodic inspection to top up Hydrator-3.3. C3 - The suspended soiling is extracted by squeezing between an absorbent towel and a smooth spatula to reduce abrasion until towel shows clean. C4 - Fat liquoring continues and is repeated with each almost drying cycle until saturation and is leave to slow natural drying. C5 - Fat liquored dried surface residue is driven into the leather structure by brushing in conjunction with Hydrator-3.3 until milky residue if any turns crystal clear. C6 - Surface clear moisture is extract with a cotton towel until towel shows dry. C7 - Staking, stretching, massaging or cross flexing one more time before the leather is completely dried for the desired suppleness. D - Dye Bleeding, Leather Tackiness and Stiffness Rectification: Common alkaline overexposure may be detected moist with tackiness or sliminess from the leaching or breaking of hydrogen bond between the leather protein fibers and the tanning agents. Bleeding detected with a white cotton towel is the result of the dyestuff breaking the hydrogen bond as well. Stiffness after leather was wet and dry again is the result of the fibers becoming stick together due to diminishing or leaching fat liquor, emptying out the leather structure. To rectify alkaline overexposure areas is by facilitating colloidal water movement to redistribute the leather constituents from surrounding areas back to the affected areas. In severe cases Acidifier-2.0 is highly recommend in conjunction with Hydrator-3.3 to effectively pH balance the leather structure back to its pH neutral (ISO-electric point or pI). Note, average pH of chrome-tanned leather is from 3 - 5, and vegetable-tanned leather is about 1 point lower thus more pH sensitive. Procedure sequence for rectifying alkaline overexposure of bleeding, tackiness and stiffness is as follows: Instruction: D1 - Saturate Hydrator-3.3 into the thickness of the leather to an optimum level with moisture oozing out when gently pressed between thumb and fingers. D2 - Cover up with plastic wrapping to control evaporation and let it dwell for redistributing of the leather constituents from surrounding area for up to 72hours with periodic inspection and topping up. D3 - Towel extraction test for dye bleeding, finger testing to detect and eliminate undesired tackiness or sliminess for a tactile squeaky feel and relax stiffness prior to fatliquoring. D4 - Fatliquoring continues and is repeated with each almost drying cycle until saturation and is leave to slow natural drying. D5 - Fatliquored dried surface residue is driven into the leather structure by brushing in conjunction with Hydrator-3.3 until milky residue if any turns crystal clear. D6 - Surface clear moisture is extract with a cotton towel until towel shows dry. D7 - Staking, stretching, massaging or cross flexing one more time before the leather is completely dried for the desired suppleness. E - Dye Fading Rectification: Vat-dyed leathers or aniline dyed leathers is subject to sun fading. However, the dormant dyestuff may be activated to refresh the surface with Hydrator-3.3. It will depend on richness of the dormant dyestuff and the dwell time for the hydrator to release the excess dyestuff to resurface, and result may vary from quality of original dyeing process. This is done with sufficient hydration and dwell time up to 72hours. The common practice is as follows: Instruction: E1 - The thickness of the leather is saturated or hydrated with Hydrator-3.3 to an optimum level with moisture oozing out when gently pressed between thumb and fingers. E2 - It is then cover up with plastic wrapping to control evaporation and let to dwell up to 72 hours for excess dyestuff to resurface. E3 - The plastic covering is removed and let to natural dry to observe color improvement. E4 - With color refreshing satisfaction, the leather is lightly wet back with Hydrator-3.3 again to relax its structure prior to fatliquoring. E5 - Fatliquoring continues and is repeated with each almost drying cycle until saturation and is leave to slow natural drying. E6 - Fatliquored dried surface residue is driven into the leather structure by brushing in conjunction with Hydrator-3.3 until milky residue if any turns crystal clear. E7 - Surface clear moisture is extract with a cotton towel until towel shows dry. E8 - Staking, stretching, massaging or cross flexing one more time before the leather is completely dried for the desired suppleness. F - Reverse-Transfer Suspended Soiling: Capillary action or wicking process is deployed to move penetrated and suspended soiling to resurface by reverse-transfer technique with Towel-T5. First the leather structure needs to be hydrated to facilitate colloidal water movement within the structural inter-fibrillary spaces, it will also require saturating Hydrator-3.3 to move the suspended soiling upwards. As it wicks through the Towel-T5, soiling are trapped instead of still remaining on the leather surface to be easily peeled off. In practice the following steps are adopted . . . Instruction: F1 - The thickness of the leather is hydrated to an optimum level with moisture oozing out when gently pressed between thumb and fingers. F2 - It is then cover up with plastic wrapping to control evaporation and let it dwell up to 72 hours to loosen and suspend foreign soiling particulates. F3 - The plastic wrapping is removed and replace with Towel-T5 without airspace to trap soiling as it dries instead of remaining on the surface. For it to stick onto the leather surface, the Towel-5 is spray wet with Hydrator-3.3 and brush out the air space with horsehair Brush-1 at a 45 degrees angle without tearing the towel tight. As it dries it will shrink back and tighten further sticking tight onto the leather surface. Recommend that Fatliquor-5.0 is replenished in combination at this stage especially if the leather has already show signs of cracking. Note that dried leathers with insufficient fatliquor (less then 15% fat and oil) content, when dry again will likely accelerate any existing cracking. F4 - Towel-T5 is peel off when crispy dry and surface residue erase with Eraser-4 or Eraser-5 for suede accordingly prior to fatliquoring. F5 - Fatliquoring continues and is repeated with each almost drying cycle until saturation and is leave to slow natural drying. F6 - Fatliquored dried surface residue is driven into the leather structure by brushing in conjunction with Hydrator-3.3 until milky residue if any turns crystal clear. F7 - Surface clear moisture is extract with a cotton towel until towel shows dry. F8 - Staking, stretching, massaging or cross flexing one more time before the leather is completely dried for the desired suppleness. G - Leather pH Chemistry Integrity Rectification: Leather is an amphoteric material or pH sensitive to the protein fibers. Alkalinity will shift the leather protein fiber ionic negative (-ve), while the other common leather constituents like the tanning agents, dyestuff and fatliquor are non-amphoteric and remains ionic negative (-ve). Thus like a magnet “like poles repels”, the leather constituent breaks hydrogen bond with the leather protein fiber and the leather denatures or revert to rawhide. Breaking of hydrogen bonds between the protein fibers and its constituents often manifest as tackiness, bleeding and stiffness when leather gets wet and dry again. Charging of the leather protein fibers ionic positive (+ve) has to go below its pH neutral (ISO-electric point or pI) of pH 3 - 5. Thus in extreme cases Acidifier-2.0 with a pH value of 2.0 accelerate the ionic positive (+ve) charging processes to restore the pH chemistry integrity of the leather. In practice the following steps are observed . . . Instruction: G1 - The thickness of the leather is saturated to an optimum level with moisture oozing out when gently pressed between thumb and fingers. G2 - It is then cover up with plastic wrapping to control evaporation and let it dwell up to 72 hours for chemical reaction to take place. G3 - The plastic wrapping is removed and lightly spray with Hydrator-3.3 to even out the surface and inspect for any unwanted tackiness or bleeding. G4 - Acidifier-2.0 treatment may be necessary for tackiness or bleeding control. Healthy leather that is stabilized, pH balanced and ionic positive (+ve) charged should feels squeaky instead with reduced bleeding. With satisfaction to restore the leather pH chemistry integrity, fatliquoring continues. G5 - Fatliquoring begins and is repeated with each almost drying cycle until saturation and is leave to slow natural drying. G6 - Fatliquored dried surface residue is driven into the leather structure by brushing in conjunction with Hydrator-3.3 until milky residue if any turns crystal clear. G7 - Surface clear moisture is extract with a cotton towel until towel shows dry. G8 - Staking, stretching, massaging or cross flexing one more time before the leather is completely dried for the desired suppleness. H - Fatliquor Surface Residue Cleaning: Fatliquor with its fat and oil content is essential for leather suppleness from cracking, it is meant for its structure, any surface remnants may alter its original surface luster and attracts soiling. Removing fatliquor surface residue is by brushing with appropriate brushes while spraying with Hydrator-3.3 turning the milky residue to crystal clear. When almost dry the leather is stack or massaged to dry for extra suppleness. The sequence of steps is as follows . . . Instruction: H1 - Likely mist Hydrator-3.3 on surface remnants and it will turn milky. H2 - Brush to drive the milky residue into the leather structure. H3 - Extract until towel shows dry. H4 - Staking, stretching, massaging or cross flexing one more time before the leather is completely dried for the desired suppleness. I - Leather Shrinkage Rectification: Leather shrinkage is often experience when leather is water damaged in conjunction with fast heat drying from the sun or other heat sources. Another common dry shrinkage is from intense heat of the sun or fireplace. Heat evaporates the fatliquor (fat and oil); the leather fibers shrunk, become stick together and result in stiffness. Fatliquor is the lifeblood of leathers and with deficiency the leather stiffens up and easily leads to cracking. Rectification is as follows: Instruction: I1 - The thickness of the leather is saturated to an optimum level with moisture oozing out when gently pressed between thumb and fingers with Hydrator-3.3. I2 - The leather is cover up with plastic wrapping to control evaporation and let it dwell up to 72hrs for complete hydration or saturation. I3 - When fully hydrated and relaxed it is then manipulate by staking, stretching, massaging or cross flexing the shrinkage to satisfaction. I4 - With satisfaction and allowing up to 25% combine moisture content or when a cotton dry towel remains dry from wiping and the leather is still damp with Hydrator-3.3, fatliquoring with Fatliquor-5.0 begins before the leather is completely dry. I5 - The fatliquored leather is left to slow dry and any surface shining residue is driven into the leather structure by brushing in conjunction with Hydrator-3.3 until milky residue if any turns crystal clear. I6 - The surface clear moisture is extract with a cotton towel until towel shows dry. I7 - Begin staking, stretching, massaging or cross flexing one more time before the leather is completely dried for the desired suppleness.

Leather Doctor® LeatherFatliquor-5.0 (250ml) is an anionic negative (-ve) charged micro emulsion of fat, oil and water for rejuvenating all leather types. It is typically used in conjunction after Hydrator-3.3 relaxing and opening up the fibrous leather structure. It softens the leather when dry with stretchability, compressibility and flexibility, while enhancing its rip tensile strength greatly. It is for replenishing the original fat and oil that diminishes thru sun bleaching, ageing, heat and alkaline overexposure or cleaning. On application, the water-encased molecule breaks free when ionic attraction takes place between the fat and oil with the leather protein fiber. The excess free water content wicks out leaving a breathing space behind for leather natural transpiration. The fat plumps the leather with fullness from easily collapsing into creases and wrinkles during stress or flex, while the oil lubricates the fibers so that they slide over one another smoothly like millions of inter-connecting hinges. Thus helps to keep leather at its optimum physical performance and prevent premature ageing. This universal Fatliquor-5.0 is for all leather types including pigmented, aniline, vachetta, nubuck, suede, hair-on-hide and woolskin. Leather Approximate Quantity or Percentage of Fatliquor: The quantities of fatliquor (fat and oil) contents retained in the leather after an universal tannery fatliquoring process may varies up from 14% to 16% depending on the leather types and it usage. This percentage drops as the fat and oil content diminishes or leaches through ageing, water, heat or chemical overexposure. Leather rejuvenating or fatliquor replenishing is base on weight of the leather in relation to the percentage of remaining fatliquor. A simple calculation of percentage of fatliquor topping up requirement would be as follows: If the weight of the leather in question is 100gm and fatliquor (fat and oil) content meter reading is less than 1%. By applying 80gm of Fatliquor-5.0 to it will deliver an end result incremental of 13.3% fatliquor when dry as the 66.6% water contents evaporates. In the leather rejuvenating Hydrator-3.3 > Fatliquor-5.0 > Hydrator-3.3 system, Hydrator-3.3 plays an important role by relaxing, opening up the inter-fibrillary spaces, facilitating and redistributing colloidal water movement, protonating and doing all the pre-conditioning work prior to fatliquoring including cleaning up any excess surface remnants to have a sticky-free surface. In practice with severe dryness the ratio for Hydrator-3.3 is 2 to 1 of Fatliquor-5.0. It works out to be approximately 160gm of Hydrator-3.3 plus 80gm of Fatliquor-5.0 to replenish a 100gm dry leather from less than 1% back to the original tannery up from 14% to 16% fatliquor content. In every bottle of Fatliquor-5.0 by weight content is comprises of 16.66% ionic negative (-ve) charged fat and oil, and 83.33% of water, the water content that encased the fat and oil molecule in an emulsion suspension when hydrogen bond with the ionic positive (+ve) leather protein fiber will break free and discharged clear from the leather structure to the surface. Instruction: 1- Warm-up and shake well to a full emulsion for better penetration. 2- Apply Fatliquor-5.0 and redistribute with foam brush until saturation. 3- Repeat applications each time water contents evaporate until fully saturated. 4- Drive remaining surface remnants free of milky fat and oil until it turns clear with Hydrator-3.3. 5- Allow leather to natural drying for extra softness. 6- Suppleness of leathers is further stake or massage or flex accordingly with a little wet back with Hydrator-3.3. Caution: Insufficient fatliquoring (fat and oil) content may suffer cracking from staking, massaging or flexing. Tips: 1- When crispy dry, prior surface contamination/damages may darkens as soiling particulates resurface. 2- Remove soiling particulates with Eraser-4 for all leathers including nubuck and Eraser-5 for suede. 3- Stretching the darken areas lightly will also lightens the appearance.

Leather Doctor® LeatherProtector-B (250ml) is a non-film forming, non-stick; rub-resistant protector for all pigmented, aniline and nubuck oil pull-up leather types. Leather-scented version is available as Protector-B+. Its non-film forming characteristic allows the leather to retain its breathability for leather natural transpiration. It impart a soft natural buttery-feel that essentially shield the detrimental effects if sticky soiling, while also prevents the common pesky ballpoint from ever ready rolling out its nasty ink on contact. Moreover it helps reduce friction rubs from dye transfer and releases them much easily when cleaned. Its rub-resistant protection increases the leather from wet and dry rubs. With reduced friction squeaks means translating into less stretch, scuff and abrasion to the leather.

HorsehairBrush-1 (1pc) detailing brush is design ergonomically to be an extension of our hand with a sturdy grooved grip. It is design to produce effective result easily and efficiently. It is recommend for all smooth leather for a soft and scratch-free cleaning. Its length is 7 inches with a three-row bristle 1½ inches cleaning head. Instruction: Use alike the wiping action of our auto or car windscreen wiper for large surfaces a section at a time and detailing work along lineal length of stitching rows, seams, creases and wrinkles. This brush is also used for working Adhesor-73 into leather surface damages to repair smooth it and towel extract surface excess prior to color coating.

FoamBrush-3” (1pc) is dense foam that resists tearing and shredding and carries more material. It has a solid wood handle that allows greater control for quality results. It is for controlling and spreading general solution for a more even distribution.

Towel-5 (5pcs)  Stretchable lint-free paper towel works like cloth, highly absorbent and washable. General application is for: a) Extracting suspended soiling during the wet cleaning process. b) “Reverse Transfer” technique with its unique stretchability during wet application and shrinking with tightening up during the drying process, this phenomenon allows the suspending or migrating soiling particulates to wick through and easily peeling off the stain when crispy dry, instead of still remaining on the leather surface. The strength of this single ply allows the wet paper to further work with a combination of spraying-on and horsehair Brush-1 without separating, creasing or tearing, thus ensuring an efficient airtight seal with an even essential surface contact. c) “Reservoir” to hold hydrator and fatliquor slow processes of dwelling or penetrating through semi-absorbent leathers, micro crazing, stitching rows and perforated leathers; or on vertical panels for flow control.d) Folding up to use as products applicator both for spreading, padding and blotting of excess. Sold in a pack of 5 pieces (size 11” x 10.4”).

Visit: www.LeatherCleaningRestorationForum.com for technical help and support.

Email: info@leatherdoctor.com for other information.